On an automated assembly line, a pneumatic line that ran fine at commissioning went soft and began to bulge after a few months. The hose was the right size and the right pressure rating. The culprit was oil mist carried in the compressed air from a lubricating compressor, which slowly worked into the silicone.To confirm that a silicone hose is compatible with a medium, you need four facts: what the medium is, how concentrated it is, how hot it runs, and how long it stays in contact with the hose. A general statement such as "silicone resists chemicals" does not answer any of them. This guide shows how to check each one, whether you are buying Reinforced Silicone Pipe for a new machine or replacing a line that keeps failing.
What Media Actually Touch the Hose in Automation Equipment
Automation equipment rarely carries just one clean fluid. Over a year of operation a hose may meet several media, some of which nobody listed in the specification.
Compressed Air With Oil Mist, Coolants and Cleaning Agents
Compressed air looks harmless, but air from a lubricated compressor or an in-line lubricator carries a fine oil mist. Coolant splash on machine tools and wash-down chemicals on food and packaging lines add to the exposure. A Silicone Hose for Compressed Air can work well on a dry, clean line at moderate pressure. With oil mist, the answer changes.
Lubricants, Hydraulic Oil and Process Fluids
Gear oil, hydraulic oil, cutting fluid, and greases are common around moving parts. The hose may touch them inside (as the carried fluid) or outside (as drips and spray). Both count. A hose that is chemically safe on the inside can still swell from the outside.
Water, Glycol, Food Liquids and Mild Chemicals
This is where silicone does best. Deionized water, cooling water, water-glycol mixtures, dilute cleaning solutions, and many food liquids pose little trouble. A Braided Silicone Hose is widely used for these lines in packaging, dosing, and cooling circuits inside automation cells.
How Silicone Reacts to Different Media
Swelling, Softening and Hardening Explained
When a medium is absorbed into rubber, the hose swells in volume, softens, and loses strength. That is Silicone Hose Swelling in plain terms. In reinforced hose the damage goes further: the swollen rubber pulls away from the fabric plies, and the hose bulges or delaminates.
The opposite can happen too. Some media extract plasticizers or low-molecular components from the rubber, and the hose shrinks and hardens. Heat and ozone can also stiffen the material over time, though silicone handles both better than most rubbers.
Why Temperature and Concentration Change the Result
A compound that is fine in a fluid at 20 °C may fail at 80 °C, because higher temperature speeds absorption. Concentration matters in the same way. A 2% alkaline cleaner is a different test from a 20% one. Contact time also counts: a one-minute rinse is not a year-round immersion.
Common Media and Silicone Reaction
|
Medium |
Typical Swelling |
Suggestion |
|
Water, water-glycol |
Very low |
Suitable |
|
Dilute acids and alkalis (low concentration) |
Low |
Suitable to conditional; check temperature |
|
Ethanol, isopropanol |
Low to moderate |
Conditional; test your grade |
|
Food liquids (milk, juice, syrup) |
Very low |
Suitable with food-grade compound |
|
Light oil mist in air |
Low, builds up with time |
Conditional; test and monitor |
|
Mineral lubricating oil, hydraulic oil |
Moderate to high |
Not recommended for continuous contact |
|
Diesel, gasoline |
High |
Not recommended |
|
Aromatic solvents (toluene, xylene) |
Very high |
Not recommended |
|
Silicone-based grease or oil |
Moderate |
Conditional; keep contact limited |
|
Low-pressure steam, hot water |
Low, but hydrolysis risk at high temperature |
Conditional; short exposure only |
These are reference ratings. Real results depend on the compound, the exact fluid grade, and the conditions.
How to Read a Chemical Compatibility Chart Without Getting Misled
A Silicone Hose Chemical Resistance Chart is a good first filter, but it has blind spots.
Test conditions are often unstated. Most charts are based on immersion at room temperature. Your line may run hotter.
Ratings differ between publishers. "A" or "Good" in one chart may mean something milder in another. Read the legend.
Mixtures are not covered. A fluid with additives, or a blend of two media, can behave differently from either component alone.
Long-term contact is hard to capture. A rating based on a 7-day test does not tell you what happens after 12 months.
Compounds vary. The chart may refer to a general silicone, while your hose uses a specific formulation.
Treat a chart as a reason to test, not a reason to skip testing. If a medium falls under "conditional" or is not listed, ask for a soak test.
How to Test Compatibility Before You Order
Simple Immersion Test (ISO 1817) and What to Measure
ISO 1817 describes how to test the effect of liquids on vulcanized rubber. The principle is simple. Take a sample of the hose compound, weigh it, measure it, and record its hardness. Immerse it in your fluid at your working temperature for a set time, then measure it again.
Weight, Volume and Hardness Change Limits
The key readings are change in mass, change in volume, change in hardness, and visual condition. As a rough screen, volume change under about 10% is comfortable, between 10% and 30% calls for caution, and above 30% usually means the material is wrong. Hardness should stay within about ±10 Shore A. Your own specification should set the real limits.
Test Items and Common Criteria
|
Test Item |
Common Criterion |
Note |
|
Volume change |
Under about 10% preferred |
Higher values need a design review |
|
Mass change |
Similar trend to volume |
Easy to check on a simple scale |
|
Hardness change |
Within about ±10 Shore A |
Softening points to absorption |
|
Tensile strength after test |
Retain most of the original value |
Agree on a limit with the supplier |
|
Visual and ply bond check |
No bubbles, cracking, or ply separation |
Cut the hose and look inside |
For a reinforced hose, also run a test on a full piece of hose, because the bond between layers is not captured by a rubber coupon alone.
A Real Scenario: Pneumatic Line Ruined by Oil Mist
A buyer (anonymous) used a Braided Silicone Hose on the air supply of a packaging machine. The fluid was listed as "compressed air," and nobody questioned it. After about five months, the hose softened and bulged near the fittings.
The compressor used a lubricated design with an in-line lubricator, and a small amount of oil mist rode in the air stream at all times. Lab checks showed a noticeable gain in hardness loss and volume in the inner layer. The team tested three options: an oil-separating filter, a different hose material, and a fluorosilicone version. They chose the filter plus a regular replacement interval, because the line pressure was low and the cost of a material change was not justified. The lesson was that the real medium is not always the one written on the drawing.
When Silicone Is Not the Right Material
Silicone has limits, and a good supplier will say so. If oil or solvent is the main medium, other materials may serve better.
Material Comparison
|
Material |
Oil Resistance |
Steam / Hot Water |
Temperature Range |
Price Level |
|
Silicone |
Poor to fair |
Fair; limited by hydrolysis |
About -50 to 200 °C |
Medium to high |
|
FKM (fluoroelastomer) |
Excellent |
Poor to fair |
About -20 to 200 °C |
High |
|
NBR (nitrile) |
Good |
Poor |
About -30 to 100 °C |
Low |
|
EPDM |
Poor |
Excellent |
About -40 to 150 °C |
Low to medium |
|
PTFE-lined |
Excellent |
Good |
About -60 to 260 °C |
High; stiff |
Silicone Hose Oil Resistance is its weak spot. For oil-bearing media, NBR or FKM is usually the safer pick. For hot water and steam, EPDM often wins. Silicone remains the best choice where flexibility, a wide temperature range, or clean contact for food and pharma matter more than oil resistance.
Compliance and Contamination Concerns
For food and medical lines, check FDA 21 CFR 177.2600 and LFGB, and ask for a report that names the actual compound used in your hose. For general industrial equipment, REACH and RoHS are common requirements in export markets.
Automation lines have another concern that is rarely listed: contamination. Silicone can release low-molecular siloxanes, which settle on surfaces. In paint shops these cause craters and poor adhesion, and on electronics assembly lines they can disturb contacts and bonding. If your equipment sits near coating, painting, or electronics work, ask for a post-cured, low-volatile grade and a statement on siloxane content.
Industry Trends
Three changes are making compatibility checks more important. Automated lines are being built to cleaner standards, so any outgassing or particle release from a hose is less tolerated. New coolants and cleaning agents keep entering the market, often with additives that older charts do not cover. And more buyers now ask suppliers for compatibility test data as part of the approval process, not after a failure. Suppliers of Reinforced Silicone Pipe who can show immersion data for common media have a clear edge.
What to Ask a Reinforced Silicone Hose Manufacturer About Compatibility
A supplier who understands compatibility will ask you questions before it quotes. Be wary of one who answers "yes, it works" to every medium. Ask these:
What compound is used, and can you share a general formulation description (platinum-cured or peroxide-cured, food-grade or standard)
Have you done immersion tests with media similar to mine, and can I see the data
Can you test my fluid on a sample before the order
What do you advise if my medium falls in the conditional range
Then fit a sample on the real equipment for a trial period. Inspect it for swelling, softness, and surface changes at regular intervals before you commit to volume.
Reliable vs High-Risk Supplier
|
Check |
Reliable Supplier |
High-Risk Supplier |
|
Medium questions |
Asks for fluid, concentration, temperature, contact time |
Quotes without asking |
|
Test data |
Provides immersion results or runs your test |
Offers a generic chart only |
|
Honesty about limits |
Says when silicone is not suitable |
Says silicone works for all media |
|
Compound details |
States the type and grade |
Vague about the material |
|
Sample trial |
Encourages a trial fit |
Pushes for a large order first |
Get Samples and a Quote
Send us the medium, its concentration, the temperature, the working pressure, and the inner diameter and length you need. We will first judge compatibility with you, then arrange samples and a quotation, and share test data where we have it. Buyers who order regularly or resell to others can also ask about Braided Silicone Hose Wholesale terms
FAQ
Q: What chemicals are compatible with silicone hose?
A: Water, water-glycol, dilute acids and alkalis, many food liquids, and some alcohols are generally fine. Strong solvents, fuels, and most oils are not. Check concentration and temperature, and test when the medium is not clearly in the safe group.
Q: Does silicone hose resist oil and grease?
A: Not well. Mineral and hydraulic oils cause swelling and softening, and some greases do too. Light oil mist may be acceptable at low levels, but it should be tested. For oily media, consider NBR or FKM.
Q: How do I test hose compatibility with a fluid?
A: Use an immersion test based on ISO 1817. Weigh, measure, and check the hardness of a sample, soak it in your fluid at working temperature, then measure again. Cut the hose open afterward to check the ply bond.
Q: Can silicone hose be used for compressed air lines?
A: Yes, for clean, dry air at moderate pressure. Reinforced types handle higher pressure. If the air carries oil mist, use an oil-separating filter or choose a more oil-resistant material.
Q: Can silicone hose contaminate my product or process?
A: In food and medical lines, a food-grade compound with the right certificates is safe. In painting or electronics environments, low-molecular siloxanes can be a concern, so ask for a low-volatile, post-cured grade.
Q: How do I judge compatibility with a mixed medium?
A: A mixture can act differently from each part. Test the actual mixture, at actual concentration and temperature. If a test is not possible, give the supplier the full composition and ask for a written opinion.
Q: Can you provide immersion test data?
A: Ask your supplier directly. Reliable manufacturers can show data for common media or run a test on your fluid. Request volume, hardness, and tensile changes with the test conditions stated.
Q: What information should I include when asking for a quote?
A: Give the medium and concentration, temperature range, working pressure, inner diameter, length, quantity, how the hose is installed, and any certificates you need.
